The Mantus M2 is the Mantus scoop anchor without the roll bar, and on the maker's numbers and the SV Panope tests it is a strong anchor wherever the seabed has some sand in it and an ordinary one in soft, sand free mud, where it fouled and failed to reset. For a 40 ft cruising cat the size that fits the maker's own chart is the 55 lb (25 kg), not the 45, and Rocna's chart lands in the same place for its Vulcan. We have not tested it. In October 2026 the M2 was nominated in the deck equipment category of the DAME Design Awards, covered in our Metstrade 2026 shortlist preview. Mā Tori's listing does not itemise her ground tackle, so this is a specification review, the one we would want to read before spending AUD 1,500 on the steel that holds the whole boat.
What it is
The Mantus M2 is a concave fluke anchor with a weighted tip and no roll bar, bolted together from a shank and a fluke with one bolt so it breaks down for stowage. It comes in 13 sizes from 8 lb to 175 lb. The galvanised version has a high tensile ASTM A514 shank on a mild steel fluke, hot dip galvanised; there is a 2205 duplex and 316L stainless version too. Made in Texas. Lifetime warranty to the original buyer on shank and fluke, three years on the galvanising. The one on sale today is the M2 Performance; the M2 Original is discontinued.
The point of taking the roll bar off is bulk and weed. Mantus still says the M1, roll bar on, rolls upright better in soft silt. The M2 is the one that fits a bow roller with a sprit or a pulpit in the way.
What Mantus claims
From the product page only:
- It sets on the first attempt, every time (the page title).
- The ears on the fluke act as foils that hold the best angle of attack, and Mantus says they almost double the soft mud holding.
- Without the roll bar it is less bulky and less likely to plug up with muddy weed than the M1, and the geometry lets it roll over without one.
- The sizing chart has three columns: day anchor under 30 knots, cruising under 50 knots, storm over 50 knots. Mantus says most cruisers should use the cruising column and go up a size when the boat sits between two. It also calls competitors' charts dangerously undersized, which is a sales line as much as an engineering one.
For a 40 ft boat under 30,000 lb (13.6 tonnes) that chart reads 45 lb day, 55 lb cruising, 65 lb storm. Those are the maker's words. Next, what happened when someone put one on the bottom and pulled.
What the independent testing says
Steve on SV Panope has put more anchors on the bottom on camera than anyone we know of, with the load measured, the set filmed underwater and the pull reversed through 180 degrees to see whether the anchor resets. He has tested the M2 three times: a 17 lb in March 2021 (test 103), a 44 lb in April 2021 in four seabeds (test 108), and a second 45 lb in February 2022 after Mantus sent a replacement because, in his words on the 45 lb retest video, the first one "had a small manufacturing flaw in the fluke that I theorized might have been the cause of some performance irregularities." A maker sent a second sample because the first was built wrong, and the tester said so in public.
His written M1 versus M2 summary, posted on Cruisers Forum and reposted by dealers, is the clearest read of the results. The M2 holds very well in seabeds with some sand in them and poorly in soft mud with none. In sandy mud it re-engaged and held after 180 degree reversals. In soft mud at Sucia Island it fouled and failed to reset, where the M1 reset on a straight pull. The M2 did not bend in his testing, and he has bent six anchors over the years. Two gripes: the tall shank sits a bit wobbly in a bow roller even with the windlass tight, and the slot the shank sits in can trap seabed, though it sprays out or clears when you pull the bolt. His conclusion is that roll bar anchors (M1, Viking, Rocna) do better in the worst, softest seabeds.
Practical Sailor's history with Mantus matters too. In January 2014, updated in 2019, PS reported that its earlier test had judged the Mantus shank "the weakest of all anchors of a similar design", that Mantus moved to a 700 megapascal shank for anchors sold after 8 December 2013, and that the bolts on PS's test anchor were stamped 307A rather than the Grade 5 the maker said it shipped. That was the M1, twelve years ago, and the M2 shank is now A514. But one bolt still holds the anchor together, and we would still look at the stamp.
Boating New Zealand's August 2025 anchor piece tests nothing but gives the local read, scoop anchors like Rocna and Mantus for most NZ bottoms, and one line that matters here. "A 40ft catamaran may require an anchor rated for a 60ft monohull due to increased load in gusts and swing radius."
Why sizing is different on a cat
A cat loads its anchor with windage, not weight. Two hulls, a bridgedeck, a bimini and 7 metres of beam present a lot of boat to a 40 knot gust, and a cat sails around at anchor unless the bridle is set right, so the snatch loads come from an angle. The chart row you read is the length row, and the Fusion 40 is 12.2 m overall. The builder never published a displacement figure, and for an anchor that matters less than you would think: the load is windage and surge, and the hull weight only picks the chart row.
Rocna is explicit on its anchor sizing guide: use the chart as instructed, then go one size larger for a multihull, with the whole chart based on "50 knots of wind, associated surge, and poor holding bottoms." A 12 m boat up to 10 tonnes is a 20 kg Vulcan, so a 12 m cat is the 25 kg. Mantus gives no multihull rule, so the honest reading of its chart is the cruising column at least, 55 lb (25 kg), and the storm column, 65 lb (30 kg), if you leave the boat on the anchor through a blow. Two charts, same answer for a 40 ft cat: 25 kg and no smaller. The 55 lb M2 is 24.9 kg, 81 cm long and 58 cm wide on the dealer table, so measure the roller and sprit before you order.
Scope is the other half of the sum. The anchor scope calculator does the chain to lay and the swing circle, and the cyclone season plan covers where the fleet sits when no anchor is enough.
What we would check before buying
- The bow roller. Panope's note about the tall shank wobbling in the roller is the one to test with a tape measure. Does the shank sit between the cheeks, and does the fluke clear the crossbeam and the sprit on the way up?
- The bolt. Mantus says the bolts are ASTM certified and oversized, with a locking washer and a pinned slotted nut. Check the grade stamp on the head, pin it, and keep the spare.
- Your bottoms, not the brochure's. Sand and sandy mud inside the reef, the Panope results favour the M2. Soft river mud at the cyclone hole or the home berth, a roll bar anchor reset better. Buy for the worst seabed you will sleep on.
- The rest of the system. A cat's bridle and snubber take the snatch loads, and chafe is what parts first. What failed at the dock in Hurricane Lowell was mostly chafe, and it is the same lesson at anchor.
- Weight forward. 25 kg of anchor plus chain is a lot in the bows of a light cat. Ask what the boat was designed to carry there before going up a size.
Fit on a Fusion 40
The Fusion 40 anchors where the 1.4 m boats cannot, inside reef lagoons in Fiji and up shallow Northland bays, and an anchor that sets fast and holds in sand suits that life. The question for any 40 ft cat is the roller and whatever sits forward of it, because a 55 lb M2 is a bigger anchor than a 40 ft monohull would carry. We cannot tell you what Mā Tori carries now because the listing does not say. The survey checklist in the Catamaran Buyer's Pack has you drop and recover 10 m or more of chain under load, and that is the moment to look at the anchor, the bolt and the roller.
Alternatives
- Mantus M1. Same maker, roll bar on. Better in soft mud in Panope's tests, bulkier on the bow, and the hollow roll bar packs with mud and needs spraying out.
- Rocna Vulcan. The other roll bar free scoop. Rocna's Vulcan page pitches it for bow fit, and Rocna's chart with the multihull rule puts a 40 ft cat on the 25 kg.
- Spade. Lead ballasted tip, two piece. Morgan's Cloud (paywalled, so no link) reports it passed every reset test in Panope's series and recommends it as the bower.
Price and where to buy
Marine Innovations, which calls itself Australia's only supplier of Mantus products, lists the M2 galvanised 55 lb (25 kg) at AUD 1,517.07, in stock, on 28 October 2026. Mantus sells direct from the US through its own site, with no price shown on the product page. For New Zealand, ask Mantus for the nearest dealer. We have no affiliate arrangement with Mantus or Marine Innovations; the links are plain.
Anchor sizing is a safety decision. Check the maker's current chart, your insurer's wording and the Cat 1 inspection checklist before you rely on anything here.
Questions people ask about the Mantus M2
What size Mantus M2 does a 40 ft catamaran need?
On Mantus' chart a 40 ft boat under 30,000 lb is a 55 lb (25 kg) cruising anchor for under 50 knots and a 65 lb (30 kg) storm anchor above that. Rocna's one size up rule for a multihull lands a 12 m cat on 25 kg as well. Do not buy the 45 lb to save bow weight.
Does the Mantus M2 reset after a wind shift?
In SV Panope's testing it re-engaged and held after 180 degree reversals in sandy mud, and fouled and failed to reset in soft, sand free mud. Sand in the seabed is the difference.
Mantus M1 or M2?
M1 if your worst anchorage is soft mud and the bow roller has room for the roll bar. M2 if you anchor in sand and sandy mud and the roller, sprit or pulpit will not take one.
How much does the Mantus M2 cost in Australia?
AUD 1,517.07 for the galvanised 55 lb (25 kg) at Marine Innovations on 28 October 2026. Mantus sells direct from the US as well. Check before you order.
Keep reading: lay the right chain with the scope and swing calculator, plan the season around the cyclone dates, or see a bluewater catamaran for sale that has anchored in all of it.